Wednesday, June 24, 2009

Curtains


The lady I did the curtains for sent a picture. Everytime I see the finished product I think of getting to work on mine... then of course, something else comes up. Like more curtains.

Anyway, in a previous post, I showed how I did the pattern matching. Here's the finished curtains. You can also see the pillow shams I made. I'm glad she liked them.

Oh, if you're interested in purchasing this fabric, it's called Pauhana and can be found at Barkcloth Hawaii. That design is popular and one of my favorites too.

Saturday, June 13, 2009

Bias tape maker machine

I could use one of these things! Does anyone have one?

Bias tape machine

Tuesday, June 9, 2009

Matching patterns

These past few weeks, I've been working on making several sets of curtains, pillow shams, and tie backs for a client. And whenever I make curtains, there's usually pattern matching to do. It's a time consuming process, but well worth the effort as the seam comes out nearly perfect every time! I remember when I tried to do it the first time, my seams were quite obviously askew. I had to redo them. Since then, I've developed a very accurate way to match the patterns. This is how I do it.

First, match the print along the selvage edges, then trim off the selvage. In this pic the selvage is that white strip in the middle.

After trimming off the selvage edge, match the print and mark along the cut edge with pins. Here's a pic with the selvage removed, and the cut edge pin marked. You can see the pin heads here..

After marking with pins, measure twice the amount of the seam allowance. Here it's 1/2" seams, so I marked 1" below the pins.
Trim off the excess along the marks.
Now it looks like it doesn't really match anymore, but remember, there's a seam allowance. Lay them right sides together, pin along your 1/2" seam and check to make sure your print matches. Sew together using the 1/2" seam allowance. Place a few pins perpendicular to the seam in places where you want to make sure the fabric won't slip.
Check, finish edges, press your seams and voila! All Pau. Can you find the seam?
Here's a closer peek...
And that's all to it. It helps if you have a large flat surface to work on. I have to do it on the floor so the fabric can be spread out, but I usually have to work with large pieces.

Wednesday, May 6, 2009

Moulage 2nd draft

I'm trying again. Realizing I probably made some mistakes (probably from trying to take measurements alone in the middle of the night when I was tired and without a mirror), I did a more careful set of measurements in INCHES instead of using cm.

I found a few discrepancies in my first set, mainly that the measurement for my shoulder length was only 3 1/4". I had used the 10cm measurement given by KK in his book. Also, I found out that if I relaxed my shoulders, my end of shoulder measurement was now almost 1" less, and my figure width was reduced by 3/4" as well. That'll bring the BPs up for sure!
I also figured out a better way to get my across back measurement. Rather than distorting my body while trying to hold one end of the tape measure at the start point, I wrapped the tape measure around my shoulders and back, read the starting number at the first measuring point, and the ending number, then calculated what my back width was.

Okay... so here's the NEW moulage sloper I drafted.

The hip curve is still weird. But you'll see a huge difference in the shoulder slope and bust points. I'm not so saggy after all! LOL Now, I have to sew this one up and see if it's any better...

Tuesday, May 5, 2009

Zee Moulage ez constructed...

Boy... mine sure looks bad. But thanks to Ada on the PR message board, I think I can make it work. Here's what it looks like now...
ACK! I have no waist! I actually do have a little bit of waistline... it just doesn't show here. My bust points are way too low (my boobs are not that close to my waistline yet), and I think the armholes are a little too tight or something. Maybe it's the shoulders...



Now in the back, I need to adjust something... I think it's the slight sway back adjustment. I may have to add a little bit more space across the back.

Here's what I plan to try (thanks Ada!). Raise the bust points up by 1 1/2", straighten out the waist/hip side seam, take a tiny pinch at the small of the back for the sway back adjustment, shorten the shoulder length by 1/2", and maybe lower the shoulder point a little bit.

I need to remember that it's supposed to look like a sausage casing. I keep thinking it's too tight! Too tight! If you have any suggestions, please comment... I'd like to get this thing right.